新闻资讯
网站首页 > 新闻资讯 >

在插拔DCS的卡件时应注意什么?

2023-03-10 11:19:10 来源:http://www.sdjkyqyb.com/ 53

开车到目前为止,DCS系统多次出现卡件指示灯灭现象,在进行下电、上电以及卡件插拔时需要注意什么呢?浙大中控DCS卡件厂家为您分析:
Up to now, the card indicator light of the DCS system has been off for many times. What should be paid attention to when powering off, powering on and plugging the card? The manufacturer of central control DCS card of Zhejiang University will analyze for you:
1、冗余卡件
1. Redundant card
先尝试将卡件进行下电,下电稍微等待1分钟后重新上电。如果还不能恢复正常,则再次下电,并将卡件重新插拔。如还不能恢复正常,则需要进行卡件更换,卡件更换前要注意新卡件的版本是否与原卡件一致,如果不一致,则需要先进行版本升级。
First try to power down the card, and then wait for 1 minute before powering up again. If it cannot return to normal, power off again and plug the card again. If it cannot return to normal, it is necessary to replace the card. Before replacing the card, pay attention to whether the version of the new card is consistent with the original card. If not, it is necessary to upgrade the version first.
在卡件插拔之前,如果涉及到带联锁的仪表,视重要程度对其进行打假值。如果涉及重要控制回路的,应将对应阀门打到手动状态。
Before card plugging, if the instrument with interlocking is involved, the false value shall be checked according to the importance. If the important control circuit is involved, the corresponding valve shall be set to the manual state.
浙大中控DCS卡件
2、非冗余卡件
2. Non-redundant card
同冗余卡件一样,还是首先尝试将卡件进行下电,下电稍微等待1分钟后重新上电。如果还不能恢复正常,则再次下电,并将卡件重新插拔。如还不能恢复正常,则需要进行卡件更换,卡件更换前要注意新卡件的版本是否与原卡件一致,如果不一致,则需要先进行版本升级。
As with the redundant card, it is still the first time to try to power down the card, and then wait for 1 minute to power up again. If it cannot return to normal, power off again and plug the card again. If it cannot return to normal, it is necessary to replace the card. Before replacing the card, pay attention to whether the version of the new card is consistent with the original card. If not, it is necessary to upgrade the version first.
与冗余卡件不同的是,非冗余卡件重新上电或者插拔后,要对其进行下装才能使用。注意下装卡件的时候使用loadwithcontent选项。
Unlike redundant cards, non-redundant cards can only be used after they are powered on or plugged in and out again. Note that the load with content option is used when loading cards.
此外操作时必须带上防静电手套或其他静电用具,以避免因静电烧坏卡件上的电子元器件。除此之外,应严格按照技术资料的要求进行操作。更多相关内容就来我们网站http://www.sdjkyqyb.com进行咨询了解!
In addition, anti-static gloves or other static appliances must be worn during operation to avoid burning the electronic components on the card due to static electricity. In addition, the operation shall be carried out in strict accordance with the requirements of technical data. Come to our website for more relevant content http://www.sdjkyqyb.com Consult and understand!
产品推荐
新闻推荐