新闻资讯
网站首页 > 新闻资讯 >

dcs卡件XP313中操作员站部分有何注意点?

2022-08-24 14:20:12 来源:http://www.sdjkyqyb.com/ 53

DCS卡件分很多种,下面来讲解的点是浙大中控dcs卡件XP313中操作员站部分有何注意点,来看看吧。
There are many kinds of DCS cards. The points to be explained below are the operator station in the xp313 of the central control DCS card of Zhejiang University. Let's have a look.
操作员站是一台工业用PC机,其基本结构和普通的台式计算机没有本质的不同。当一台PC机出现故障时,先要使用插拔法、替换法、比较法来确定PC机中是何部件有故障,然后针对性地更换故障部件或更换插槽(更换PC机部件一般应由工程技术人员在现场指导)。
The operator station is an industrial PC, and its basic structure is not fundamentally different from the ordinary desktop computer. When a PC fails, it is necessary to use the plug-in method, the replacement method and the comparison method to determine which parts in the PC are faulty, and then replace the faulty parts or replace the slots (the replacement of PC parts should generally be guided by the engineering and technical personnel on the site).
为了避免盲目地更换部件,可根据PC机启动时的报警声数来判断故障所在。
In order to avoid blind replacement of components, the fault can be determined according to the number of alarm sounds when the PC is started.
当显示器显示不正常,并排除了工控机故障时,可检查一下显示器的按钮设置。确定显示器前部“D-SUB/BNC”按钮位置:若显示器背部信号线连接是通过15针D型接口电缆,该按钮置于“D-SUB”位置;若显示器背部信号线连接是通过BNC型接口电缆,该按钮置于“BNC”位置。
When the display is abnormal and the industrial computer fault is eliminated, check the button setting of the display. Determine the position of the "D-sub / BNC" button on the front of the display: if the signal line on the back of the display is connected through the 15 pin D-type interface cable, the button is placed at the "D-sub" position; If the signal line on the back of the display is connected through the BNC type interface cable, the button is placed at the "BNC" position.
浙大中控dcs卡件XP313
若显示器背部信号线连接是通过BNC型接口电缆,确定同步信号开关“Sync.Switch”的位置:如果用绿色同步信号(3BNC)模式,该开关设在“S.O.G.”位置;如果用H、V分离型同步信号(5BNC)或H+V混合型同步信号(4BNC)模式,该开关设在“H/V”位置。
If the signal line on the back of the display is connected through the BNC interface cable, determine the position of the synchronization signal switch "sync. Switch": if the green synchronization signal (3bnc) mode is used, the switch is set at the "s.o.g." position; If the H and V separated synchronization signal (5bnc) or H + V mixed synchronization signal (4bnc) mode is used, the switch is set to "H / V" position.
当显示器颜色不纯,可按显示器前部“消磁”按钮以消除电磁干扰。若显示器按钮设置正确,而显示仍不正常,可用备用显示器或办公用显示器暂时先替换上,再和供应商联系显示器维修事项。
When the color of the display is not pure, press the "demagnetization" button on the front of the display to eliminate electromagnetic interference. If the display button is set correctly and the display is still abnormal, the standby display or office display can be replaced temporarily, and then contact the supplier for display maintenance.
dcs卡件XP313中操作员站部分有何注意点?以上从两个方面来讲解了问题,更多内容就来我们网站http://www.sdjkyqyb.com咨询吧。
What are the precautions for the operator station in the DCS card xp313? The above explained the problem from two aspects. For more information, please visit our website http://www.sdjkyqyb.com Consult.
产品推荐
新闻推荐