新闻资讯
网站首页 > 新闻资讯 >

搞懂DCS点检的相关部件过程

2022-08-10 14:08:13 来源:http://www.sdjkyqyb.com/ 53

应用在工业生产中的DCS系统,必然会因为一些不良因素的影响,而导致系统性能下降。所以须定期对DCS系统进行全面的检查和维修,尤其是可能引起系统故障的关键点进行检测和必要的部件更换,下面就跟着浙大中控操作员软件狗制造厂家来搞懂DCS点检的相关部件过程。
The DCS system applied in industrial production will inevitably lead to the decline of system performance due to the influence of some adverse factors. Therefore, it is necessary to conduct comprehensive inspection and maintenance on the DCS system regularly, especially to detect the key points that may cause system failure and replace the necessary components. Next, follow the manufacturer of the central control operator software dog of Zhejiang University to understand the process of DCS point inspection.
中控室环境检查
Environmental inspection of central control room
1.检查空调运转情况:温度要求16-25℃,湿度要求40%-90%。
1. Check the operation of the air conditioner: the temperature shall be 16-25 ℃, and the humidity shall be 40% - 90%.
2.检查清洁状况:门窗应关好,注意防尘。电缆的孔洞要求密封。
2. Check the cleanliness: the doors and windows should be closed properly and pay attention to dust prevention. The holes of cables shall be sealed.
3.检查操作台安装情况:应牢固没有振动。
3. Check the installation of the console: it shall be firm and free of vibration.
电子间环境检查
Environmental inspection of electronic room
1.检查空调运转情况:温度要求16-25℃,湿度要求40%-90%。。
1. Check the operation of the air conditioner: the temperature shall be 16-25 ℃, and the humidity shall be 40% - 90%..
2.检查清洁状况:门窗应关好,注意防尘。电缆的孔洞要求密封。
2. Check the cleanliness: the doors and windows should be closed properly and pay attention to dust prevention. The holes of cables shall be sealed.
浙大中控操作员软件狗
3.检查防静电地板情况:地板的支架应连接可靠稳固。
3. Check the anti-static floor: the support of the floor shall be connected reliably and firmly.
系统接地检查
System grounding inspection
1.操作台:操作台要求接地,台内插座的地线要求接地,均为保护地。
1. Operation console: the operation console is required to be grounded, and the ground wire of the socket inside the console is required to be grounded, which is protective ground.
2.IT设备:计算机主机的外壳、服务器的外壳和交换机的外壳必须接保护地。
2. IT equipment: the shell of the computer host, the shell of the server and the shell of the switch must be grounded.
3.电源柜:柜体要求接地,为保护地。
3. Power cabinet: the cabinet is required to be grounded, which is a protective ground.
浙大中控操作员软件狗系统清灰
Cleaning of the software dog system of the central control operator of Zhejiang University
1.使用吹吸风机、抹布、毛刷等工具对操作台、显示器、计算机主机、键盘、交换机、光纤收发器及同类设备、机柜、散热风扇、主控单元、电源、模块等设备进行清灰。
1. Use blowing and suction fans, rags, brushes and other tools to clean the operation console, display, computer host, keyboard, switch, optical fiber transceiver and similar equipment, cabinet, cooling fan, main control unit, power supply, module and other equipment.
2.使用超声波清洗仪对模块板卡进行清灰。(一般情况下不需要本项检查)
2. Use the ultrasonic cleaner to clean the module card. (this inspection is not required in general)
3.更换损坏的机柜散热风扇和机柜滤网。
3. Replace the damaged cabinet cooling fan and cabinet filter screen.
搞懂DCS点检的相关部件过程,实际上的目的是将系统故障消除在萌芽状态,延长系统使用寿命,保证DCS系统长期、安全、稳定运行。还有什么不懂得地方随时来我们网站http://www.sdjkyqyb.com咨询了解。
The purpose of understanding the process of DCS point inspection is to eliminate the system fault in the bud, extend the service life of the system, and ensure the long-term, safe and stable operation of the DCS system. If you don't know anything, please come to our website at any time http://www.sdjkyqyb.com Consultation and understanding.
产品推荐
新闻推荐